Insane amount of Toyota parts

I just acquired a TON of toyota parts. I have about anything you can think of. If you are looking for anything post up or give me a call at (256) 587-9208.  Thanks.

I've got several rear axles and the alternator bracket that you've been wanting. I have several birfields but I'm keeping them for myself. Sorry    No luck on the 4-runner panels.

I am looking for a rear Toy double cardon driveshaft.  And I don't want the one off of your wrecked truck. I may end up running one on the front of my Zuk.  JC

rolltidezuk wrote: I am looking for a rear Toy double cardon driveshaft.  And I don't want the one off of your wrecked truck. I may end up running one on the front of my Zuk.  JC

You need a front driveshaft from an IFS truck. Toyota did not use a CV on the rear. You have to make one from a front. I have several. How about $60 for one?

Chappy wrote: i need a couple driveshaft flanges and velocity joints

What year are you needing? There are several different bolt patterns on toy driveshaft flanges and CV's. I have some of each. Thanks.

im runnin drilled flanges so i dont think it would matter

Edited by Chappy

i need complete driveshafts or just the flanges for the driveshafts that the ujoint is in

YEAH i can...i cant use toyota slip yokes bc they dont slip enough...what kind of trading are you thinkin?

What would the price be for a front cv axel for a 87 ifs

M DODSON wrote: What would the price be for a front cv axel for a 87 ifs

 

How about $25 ?

$30 sounds good.

There are a few runners at HWY 79 auto salvage , located about 2 miles from the bottom of Skyline on hwy 79. I don't know if they're any good , I just know he has some.

do you have an airflow meter/airbox cover for a 22re? If so, how much?

sushi

I am all over one for $20, tell me how to get in touch with you or where I can pick it up.

sushi

Sushi , I'll pm you my work # . I'll also be at our meeting this wednsday night if you want to pick it up there.

MDodson , sounds like you have some bad electrical problems. I don't have a good harness for an '87.

I can use the fuse box and about a foot of wire from a 87 pickup or what ever matches.

I am not sure if a 85 will work or not

do you have a power steering pump?.... puting power steering on my toy

thanks,

bryon mead

Byron, I have a PS pump. I have steering boxes also if you need one. I'll take $100 for both or $40 for a pump.

 

Slamchops , I have 1 extra axle thats not in a housing.$25. I hate to take a complete '86 + rear end apart just for the axles. I have a complete '89 v6 rear end if anyone needs one. I have several 4cyl rear ends also.

I have some tail lights lenses too, but you can buy them new for almost nothing.

 

new, theyre $20 a pop from certifit. i'd rather find some cheap cuz i know they wont last forever. how hard would it be to ship that axle shaft to south AL ?

Chappy, I have more PS pumps if you want one.

Slamchops, I'll take $15 for both lenses if you want them. How's $60 for an AC compressor and lines? As for shipping , you can call me and we'll discuss it. Thanks

Are you going to the meeting tomorrow?  I'm still interested in the Front CV axel for an '87 Toyota pickup for $25.

i tried calling twice this afternoon. 

Nick I tried to pm you about the winch mount you were talking about today, would you take $250 for it? That is about all I can scratch together right now.

jay

i've tried calling all weekend and no luck. can you pm me a price on shipping? 

What's your bottom dollar on the transfer case doubler?  very interested.

sorry, I read it wrong

 

It comes with the bracket and idler pulley, but I don't have a resovoir or lines. I might can find one if you need me to. Thanks.

I don't have either one in good condition. I can build you a back bumper if you want me to.

what kind of price on a back bumper that you can make

Hey Nick,

ill take the pump, bracket,and pulley. Is this all still $40? ill have my dad call you at work.Also, about the carb. and swap on tranny. is that still a go?  thanks much.

i have a chrome tube bumper for a toyota if you still need a bumper pm me

I have several. What year would you like?

Yeah , I have one. $5 if you pick it up.

Nick, besides the steering shaft, I also need a rear driveshaft from an ifs truck if you have one.  JC

I have one front toy shaft to use on my Zuk rear, But I could use a spare. On the rear shaft either long or short wheel base will work, because it will have to be cut down. And if either has a better ujoint (will work at more of an angle), that is what I need. Do you still have a 33 I can use for a spare?  Tell me how much for all this, and I'll see you at the meeting next week.  Thanks, JC

sounds good. I'm in no hurry for the spare.  Thanks, JC

I don't have the blue '89 4-runner. Is the fill hose the same on a 4-runner as a pickup? If so I'll give you one , but I don't have one for a 4-runner.

Big Red wrote: I thought you bought the blue '89 from Danny after I sold it to him

I just got the EFI and bought the engine out of it.

 

I'll bring the hose to the next meeting.

 

hey man, still got that v6 rear axle? 

how much you want for it?

will those shafts fit the same as the 4cyl axles?


Edited by SlamChops

any spare birfs? 

I'm looking for a 4 cyl T-case.  I want one from a 84-88 truck or runner with tranny code G52, G54, or W56.  Do you have anything like that?

 

Thanks,

Jeff Posey

Madison, AL

jposey66 wrote: I'm looking for a 4 cyl T-case.  I want one from a 84-88 truck or runner with tranny code G52, G54, or W56.  Do you have anything like that?

Do you need a top shift or forward shift?

All G52's and G54's were forward shift , and 85-88 W56's were top shift. All '89-'95 W56's were forward shift. A forward shift "G" series also has different length shift rods than a forward shift "W" series.

If you need a top shift , anything from '79-'83 will work . They were all top shift.

Find out exactly what you need and I'll see what I've got.

Thanks.

Yea, the different shift rod length, on the 89-95, is why I only want one through 88.  I would have to swap shift rods in those cases.  I don't want 79-83, because they are "noisy run gears", per Advance Adapter, which is where I am getting most of my info on what I need.  This all narrows it down to 84-88 and leaves a choice of forward shift or top shift.  I think, for my application, my first choice would be top shift(W56) but would also consider a forward shift(G52, G54).

 

Thanks,

Jeff Posey

Madison, AL

Edited by jposey66

Putting a 5.0L and AOD in an 88 V6 4runner, so I need the 4 cyl T-case.  The adapter will work with both the top shift cases and the earlier forward mounted shifter cases.  As far as the quiet vs noisy cases, it is currently very quiet, with no noises, rattles, or squeaks, except for the noise of the tires that I am about to replace.  I really like it that way and, if there is "noisy vs quiet" on anything, I want to take the "quiet" choice.

 

Jeff Posey

Madison, AL

Edited by jposey66

If you don't think it makes any more noise than the others, I may give it a try.  I'd like to come take a look at it.  Where are you located?  I am in Madison and can usually be reached on my cell at 714-5885.

 

Thanks,

Jeff

PM'd you, Nick.

No, they are not the same , and they will NOT interchange. Anything '85 to '95 will work on your '87. The '84 down 22r's had a taller block and head.

Thanks  We would be glad to have ya'll come ride with us.

I've just about got my rig finished so maybe I'll be able to get out and do some wheeling soon.

I think I just sold the only one of those I had.

Let me check and see if I have another one.

You'll need to know if it's an '84 down (dome top pistons) or an '85 up (flat tops). Thats basically all you need to know.

I would completely tear down the engine and have everything checked before you order your kit. This way you know what size pistons and bearings to order.

Check out www.22re.com  I have built 4 22R's with this kit and have had good luck so far. I don't think you'll beat it for the price either. Everything is japanese parts.

Sounds like he gave you an IFS hub. I've got one . $40

I don't have a lot of 3.0 v6 parts , so no injectors. Sorry.

If I had a high pinion 3rd it would be in my truck.

u dont happen to have a drive shaft to a 88` toyota truck ,regular cab, and how much? need the long part, sheared mine in half

where in skyline are u located? or can u bring it to the next meeting?

kewl thanks

jr hall wrote: are yall goin to be open on this monday

It's just me working on junk at my house , but yes I'll be there in the evening. Give me a call at 587-9208 after 3:30 or this weekend and I'll give you directions. Thanks.

Sure do.

Nope. Good luck finding a good xtra-cab. Your best bet is to look for a 2wd. They can be found cheap.

Yeah I've got one. $25

Will the wiring harness be the same as the 4x4 or will I have to use the one from the rolled truck. and what years should I look for. thanks for the help