|
|
12x1.25mm tap |
Post Reply 
|
| Author | |
Guests 
Guest 
|
 Post Options
 Thanks(0)
 Quote Reply
 Topic: 12x1.25mm tapPosted: 16 November 2008 at 11:31am |
|
I have looked everyehere. I need this to clean the threads on my 22re block. Where can I get one pretty quick.
|
|
 |
|
|
83K10
RCRC Club & Business Member 
Joined: 17 February 2004 Location: Huntsville, AL Status: Offline Points: 3259 |
Post Options
Thanks(0)
Quote Reply
Posted: 16 November 2008 at 12:12pm |
|
Turner mill and supply on washington would be the only place in town that would have it.
Heres one from enco. Don't buy the chinese taps. I've had them fail in several different ways. http://www.use-enco.com/CGI/INSRIT?PMAKA=510-1149&PMPXNO=944968&PARTPG=INLMK32 |
|
|
|
|
bluetoy
RCRC Club Visitor 
Joined: 17 February 2004 Location: Skyline, Jackson County Status: Offline Points: 2222 |
Post Options
Thanks(0)
Quote Reply
Posted: 16 November 2008 at 3:16pm |
|
I took an old head bolt and ground a flute in it with a razor wheel. It works really good for cleaning out the gunk in the threads of the head bolts. I work in a machine shop but we don't have anything that size either.
|
|
|
TOYOTA FOUR WHEEL DRIVE................need I say more?
|
|
|
|
|
Guests
Guest
|
Post Options
Thanks(0)
Quote Reply
Posted: 16 November 2008 at 3:54pm |
|
Thanks for the info guys. I will check out Turner like you said John. If I have no luck there than I will have to just try the homemade approach. This isnt a big deal I just like to buy the right tool for the job even if I only use it once I will always have one.
|
|
|
|
|
83K10
RCRC Club & Business Member
Joined: 17 February 2004 Location: Huntsville, AL Status: Offline Points: 3259 |
Post Options
Thanks(0)
Quote Reply
Posted: 16 November 2008 at 4:26pm |
|
Patrick,
I tried to call you earlier but your phone was off. I didn't call your house cause I didn't know if you were asleep. I'm going to put an order in to Enco tomorrow. I can stick your tap on with my order and save you shipping if you want. John |
|
|
|
|
98TJ
RCRC Club Member 
RCRC Club Treasurer Joined: 10 May 2005 Location: Maysville, Madison County Status: Offline Points: 8926 |
Post Options
Thanks(0)
Quote Reply
Posted: 16 November 2008 at 5:54pm |
|
Order it from McMaster Carr (Atlanta) tonight and you will have it Tueday.
|
|
|
1998 TJ 4.0 5spd Atlas 36" Swampers RE4.5 ARB's 44/44
2015 JK Rubicon, mostly stock |
|
|
|
|
alabamatoy
Admin Group
I dont work here anymore... Joined: 16 February 2004 Location: Signal Mountain Status: Offline Points: 9442 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 November 2008 at 12:43am |
|
I have two of them, I think, you can borrow one if you want.....
|
|
|
"If you didnt buy your 1st gen 4Runner new, then YOU are a newbie!!"
BRC Life Member |
|
|
|
|
Guests
Guest
|
Post Options
Thanks(0)
Quote Reply
Posted: 17 November 2008 at 1:50am |
|
Yes John I'll take one. Let me know what I owe you. Much appreciated. Thanks for the offer Doc. If I cant get one I will give you a call. I just want one for my set. I have over 200 taps and dies but never realized I didnt have a 12x1.25mm tap,never needed one till now, so this just helps complete my set. |
|
|
|
|
Toydawg
RCRC Club Visitor
Joined: 20 June 2006 Location: United States Status: Offline Points: 953 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 November 2008 at 6:50am |
|
I bought a 12/125 metric tap at the Ace Hardware store in Decatur a few months ago. They have a pretty good selection of metric nuts and bolts as well.
|
|
|
1984 Toyota pickup, locked 5.29s, dual cases, Longfields, 22R with low range cam and header.
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options