Rock Slider refurb |
Post Reply |
Author | |
gumataotaom
RCRC Club Member Joined: 15 February 2014 Location: United States Status: Offline Points: 205 |
Post Options
Thanks(0)
Posted: 06 January 2017 at 8:50am |
Does anyone know of a shop or person who can sand/blast/clean up and recoat (paint, powder coat, liner or other) a set of JK 4dr rock sliders? They are about 6.5 ft long and around 14 inches wide so way to big to put in the sandblaster on the Arsenal.
Thanks, Mike
|
|
alabamatoy
Admin Group I dont work here anymore... Joined: 16 February 2004 Location: Signal Mountain Status: Offline Points: 9369 |
Post Options
Thanks(0)
|
acmc415 (Mickey Christian) on this forum was doing mobile dustless blasting, dont know if he's still doing it or not, he hasnt been on here in a while. He brought his blasting rig to one of the club meetings a year or so ago.
The auto craft shop on the Arsenal has (had?) a very large blast cabinet, probably more than 6ft in length. It works pretty well, I have used it. I was able to put my wife's roof rack in it with room to spare. Its all enclosed, with those spaceman-Spiff gloves that you use to reach in and do the work. Did you check the size? Maybe they got rid of the big one and replaced it with a small one. You can get them all clean, then take them to a powder-coater. John Griffin does a lot of work through some local powder-coater, but I dont know who it is. Be careful with sandblasting - it produces fractured silica, which is really bad stuff in your lungs. There are other kinds of media which are much safer. |
|
"If you didnt buy your 1st gen 4Runner new, then YOU are a newbie!!"
BRC Life Member |
|
gumataotaom
RCRC Club Member Joined: 15 February 2014 Location: United States Status: Offline Points: 205 |
Post Options
Thanks(0)
|
Thanks for the info. Love the sliders I have now (home made & solid mounted to frame vs the thinner body mounted ones) and have saved me quite a bit of pain over the years but those pigs need some lipstick. Debating on the cost effectiveness of the entire recoating process. |
|
alabamatoy
Admin Group I dont work here anymore... Joined: 16 February 2004 Location: Signal Mountain Status: Offline Points: 9369 |
Post Options
Thanks(0)
|
Its dirty work, but angle grinders are cheap and the "flap disks" actually work pretty well. If the sliders are removable, you could do this yourself easily, but could also do it on the vehicle, just need to mask the body to avoid damage. There may be some areas where you just can't reach.
Get an angle grinder, a facemask and some earmuffs (or plugs) and have a go at the sliders yourself. Grind 'em clean to metal, wipe the metal off with a clean rag and some MEK (use gloves) then I recommend using Rustoleum "Self Etching Primer" which you can get at HD/Lowes or Walmart automotive area. Then paint with Rustoleum whatever color. Its pretty durable as long as you let the paint dry sufficiently and use several coats. The primer dries almost instantly, so you can work on an area, clean it, prime it, and leave it for a while and come back to it. Just grind a light bit back into the primed area. Primer over primer doesnt matter. HTH Edited by alabamatoy - 06 January 2017 at 10:50am |
|
"If you didnt buy your 1st gen 4Runner new, then YOU are a newbie!!"
BRC Life Member |
|
gumataotaom
RCRC Club Member Joined: 15 February 2014 Location: United States Status: Offline Points: 205 |
Post Options
Thanks(0)
|
Yep. I have them off and started grinding on them last night. Much easier project when the weather is warmer. I was just looking for a 'more convenient' avenue. Thanks for the advice!
|
|
83K10
RCRC Club & Business Member Joined: 17 February 2004 Location: Huntsville, AL Status: Offline Points: 3178 |
Post Options
Thanks(0)
|
Powder will hold up the best on these vs paint. Kreative Koatings 256-262-4327 jessica@kreativekoatings.com is who we use. If you email her a picture and some measurements, she should be able to quote it for you with out you having to take it to them. They can also blast them for you.
|
|
gumataotaom
RCRC Club Member Joined: 15 February 2014 Location: United States Status: Offline Points: 205 |
Post Options
Thanks(0)
|
Thanks John!
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |